EXPLORE BY TASK
Crafts Tools
35 tools in this collection. Choose a task below or search the complete FeuTex toolkit.
Browse all tools
Bead Loom Warp Layout
Plan warp thread count and beadwork width from bead columns and measured bead pitch.
Open tool →CraftsBead Pattern Repeat Planner
Fit complete bead-pattern repeats between a clasp and end spacers.
Open tool →CraftsBias Strip Square Size
Estimate the square of fabric required for a desired length of continuous bias strip, allowing for unusable seam area.
Open tool →CraftsBookbinding Sewing Hole Layout
Calculate even sewing-hole spacing with protected head and tail margins.
Open tool →CraftsBookbinding Signature Planner
Round a page count to folded signatures and count blank pages and sheets.
Open tool →CraftsBoxed Pouch Flat Pattern
Translate finished pouch width, height and depth into two flat rectangles and corner cutouts.
Open tool →CraftsChainmail Ring Aspect Ratio
Calculate ring inside diameter and aspect ratio from mandrel diameter, wire diameter and measured springback.
Open tool →CraftsCrochet Flat Round Increase Check
Estimate a geometric increase count per round from measured stitch width and round height.
Open tool →CraftsCrochet Foundation Repeat Fit
Choose a foundation chain compatible with a stitch multiple and extra turning chains while approaching a target width.
Open tool →CraftsCross-Stitch Fabric and Frame Plan
Calculate stitched dimensions and fabric cut size including border and mounting allowance.
Open tool →CraftsElastic Casing and Overlap
Plan elastic cut length and fabric casing clearance from a measured body circumference and selected stretch.
Open tool →CraftsEmbroidery Floss Sample Scaling
Scale measured floss use from a test motif to the project, including strand count and working waste.
Open tool →CraftsEnvelope Pillow Back Panels
Calculate front and overlapping back panel dimensions from a finished cushion cover and chosen seams.
Open tool →CraftsFabric Pattern Repeat Alignment
Find aligned cutting lengths when a visible motif must begin at the same point on every fabric panel.
Open tool →CraftsGathered Ribbon Ruffle Plan
Estimate ribbon consumption and segment joins for a gathered trim at a chosen fullness.
Open tool →CraftsKnitting Buttonband Pickup Ratio
Estimate pickup stitches and a practical skip interval when row gauge differs from buttonband stitch gauge.
Open tool →CraftsLeather Stitch Hole Distribution
Find a whole number of stitch intervals and the adjusted pitch that fits a seam between end margins.
Open tool →CraftsMacrame Cord Length from Weight
Estimate remaining cord length from a weighed sample and determine project capacity with a reserve.
Open tool →CraftsMosaic Grout Void Volume
Estimate the joint volume between equal rectangular mosaic pieces, excluding the tile bodies.
Open tool →CraftsOn-Point Quilt Setting Triangles
Size oversized corner and side setting squares from the finished block diagonal for an on-point quilt.
Open tool →CraftsOrigami Square Cutting Yield
Count square sheets cut from rectangular stock and quantify unused paper area.
Open tool →CraftsPaper Rosette Accordion Plan
Estimate accordion strip demand and evenly spaced folds for a decorative paper rosette.
Open tool →CraftsPottery Slab Clay Mass
Estimate wet clay mass for a rectangular slab and check how much remains after trimming.
Open tool →CraftsPottery Test Bar and Target Size
Use wet, dry and fired test-bar measurements to size a new wet clay piece for a target fired length.
Open tool →CraftsQuilling Paper Tight Coil Size
Estimate the outer diameter of a tightly rolled paper strip and the strip length needed for a target coil diameter.
Open tool →CraftsQuilt Diagonal Backing Estimate
Estimate fabric length for a diagonal-spliced backing when the required width lies between one and two fabric widths.
Open tool →CraftsScreen Print Registration Margin
Check usable print area after frame borders and squeegee clearance, and center an artwork within it.
Open tool →CraftsSewing Dart Pivot Transfer
Transfer a dart angle to a different seam distance from the same pivot while preserving its angular intake.
Open tool →CraftsSmocking Dot Grid Planner
Calculate dot columns and compressed panel width for a repeated pleat grid.
Open tool →CraftsSquare-in-Square Patchwork Geometry
Determine the rotated center square size and its diagonal from the desired finished outer block.
Open tool →CraftsStained Glass Copper Foil Demand
Estimate foil length for repeated rectangular glass pieces with overlaps and waste.
Open tool →CraftsStrip Set Quilt Block Yield
Account for seams, end trimming and crosscuts when making repeating blocks from strip sets.
Open tool →CraftsWeaving Warp and Loom Waste Plan
Plan warp ends and total yarn length with edge allowance, take-up and loom waste.
Open tool →CraftsWeaving Weft Yarn Requirement
Estimate weft length from finished cloth dimensions, pick density, take-up and loom waste.
Open tool →CraftsYarn Held Together Supply
Find usable combined-strand length and the remaining yarn when holding two yarns together.
Open tool →